| EACCES | For UNIX domain sockets, which are identified by pathname: Write permission is denied on the socket file, or search permission is denied for one of the directories in the path prefix. (See also path_resolution(7).) |
| EPERM | The user tried to connect to a broadcast address without having the socket broadcast flag enabled or the connection request failed because of a local firewall rule. |
| EACCES | It can also be returned if an SELinux policy denied a connection (for example, if there is a policy saying that an HTTP proxy can only connect to ports associated with HTTP servers, and the proxy tries to connect to a different port). |
| EADDRINUSE | Local address is already in use. |
| EADDRNOTAVAIL | (Internet domain sockets) The socket referred to by sockfd had not previously been bound to an address and, upon attempting to bind it to an ephemeral port, it was determined that all port numbers in the ephemeral port range are currently in use. See the discussion of /proc/sys/net/ipv4/ip_local_port_range in ip(7). |
| EAFNOSUPPORT | The passed address didn't have the correct address family in its sa_family field. |
| EAGAIN | For nonblocking UNIX domain sockets, the socket is nonblocking, and the connection cannot be completed immediately. For other socket families, there are insufficient entries in the routing cache. |
| EALREADY | The socket is nonblocking and a previous connection attempt has not yet been completed. |
| EBADF | sockfd is not a valid open file descriptor. |
| ECONNREFUSED | A connect() on a stream socket found no one listening on the remote address. |
| EFAULT | The socket structure address is outside the user's address space. |
| EINPROGRESS | The socket is nonblocking and the connection cannot be completed immediately. (UNIX domain sockets failed with EAGAIN instead.) It is possible to select(2) or poll(2) for completion by selecting the socket for writing. After select(2) indicates writability, use getsockopt(2) to read the SO_ERROR option at level SOL_SOCKET to determine whether connect() completed successfully (SO_ERROR is zero) or unsuccessfully (SO_ERROR is one of the usual error codes listed here, explaining the reason for the failure). |
| EINTR | The system call was interrupted by a signal that was caught; see signal(7). |
| EISCONN | The socket is already connected. |
| ENETUNREACH | Network is unreachable. |
| ENOTSOCK | The file descriptor sockfd does not refer to a socket. |
| EPROTOTYPE | The socket type does not support the requested communications protocol. This error can occur, for example, on an attempt to connect a UNIX domain datagram socket to a stream socket. |
| ETIMEDOUT | Timeout while attempting connection. The server may be too busy to accept new connections. Note that for IP sockets the timeout may be very long when syncookies are enabled on the server. |
NAME
connect - initiate a connection on a socket
LIBRARY
Standard C library (libc, -lc)
SYNOPSIS
#include <sys/socket.h>int connect(int \nsockfd\n, const struct sockaddr *\naddr\n,\n
\n socklen_t \naddrlen\n);DESCRIPTION
The connect() system call connects the socket referred to by the file descriptor sockfd to the address specified by addr. The addrlen argument specifies the size of addr. The format of the address in addr is determined by the address space of the socket sockfd; see socket(2) for further details.
If the socket sockfd is of type SOCK_DGRAM, then addr is the address to which datagrams are sent by default, and the only address from which datagrams are received. If the socket is of type SOCK_STREAM or SOCK_SEQPACKET, this call attempts to make a connection to the socket that is bound to the address specified by addr.
Some protocol sockets (e.g., UNIX domain stream sockets) may successfully connect() only once.
Some protocol sockets (e.g., datagram sockets in the UNIX and Internet domains) may use connect() multiple times to change their association.
Some protocol sockets (e.g., TCP sockets as well as datagram sockets in the UNIX and Internet domains) may dissolve the association by connecting to an address with the sa_family member of sockaddr set to AF_UNSPEC; thereafter, the socket can be connected to another address. (AF_UNSPEC is supported since Linux 2.2.)
RETURN VALUE
If the connection or binding succeeds, zero is returned. On error, -1 is returned, and errno is set to indicate the error.
ERRORS
The following are general socket errors only. There may be other domain-specific error codes.
- EACCES
For UNIX domain sockets, which are identified by pathname: Write permission is denied on the socket file, or search permission is denied for one of the directories in the path prefix. (See also path_resolution(7).)
- EACCES
- EPERM
The user tried to connect to a broadcast address without having the socket broadcast flag enabled or the connection request failed because of a local firewall rule.
- EACCES
It can also be returned if an SELinux policy denied a connection (for example, if there is a policy saying that an HTTP proxy can only connect to ports associated with HTTP servers, and the proxy tries to connect to a different port).
- EADDRINUSE
Local address is already in use.
- EADDRNOTAVAIL
(Internet domain sockets) The socket referred to by sockfd had not previously been bound to an address and, upon attempting to bind it to an ephemeral port, it was determined that all port numbers in the ephemeral port range are currently in use. See the discussion of /proc/sys/net/ipv4/ip_local_port_range in ip(7).
- EAFNOSUPPORT
The passed address didn't have the correct address family in its sa_family field.
- EAGAIN
For nonblocking UNIX domain sockets, the socket is nonblocking, and the connection cannot be completed immediately. For other socket families, there are insufficient entries in the routing cache.
- EALREADY
The socket is nonblocking and a previous connection attempt has not yet been completed.
- EBADF
sockfd is not a valid open file descriptor.
- ECONNREFUSED
A connect() on a stream socket found no one listening on the remote address.
- EFAULT
The socket structure address is outside the user's address space.
- EINPROGRESS
The socket is nonblocking and the connection cannot be completed immediately. (UNIX domain sockets failed with EAGAIN instead.) It is possible to select(2) or poll(2) for completion by selecting the socket for writing. After select(2) indicates writability, use getsockopt(2) to read the SO_ERROR option at level SOL_SOCKET to determine whether connect() completed successfully (SO_ERROR is zero) or unsuccessfully (SO_ERROR is one of the usual error codes listed here, explaining the reason for the failure).
- EINTR
The system call was interrupted by a signal that was caught; see signal(7).
- EISCONN
The socket is already connected.
- ENETUNREACH
Network is unreachable.
- ENOTSOCK
The file descriptor sockfd does not refer to a socket.
- EPROTOTYPE
The socket type does not support the requested communications protocol. This error can occur, for example, on an attempt to connect a UNIX domain datagram socket to a stream socket.
- ETIMEDOUT
Timeout while attempting connection. The server may be too busy to accept new connections. Note that for IP sockets the timeout may be very long when syncookies are enabled on the server.
STANDARDS
POSIX.1-2008.
HISTORY
POSIX.1-2001, SVr4, 4.4BSD, (connect() first appeared in 4.2BSD).
NOTES
If connect() fails, consider the state of the socket as unspecified. Portable applications should close the socket and create a new one for reconnecting.
EXAMPLES
An example of the use of connect() is shown in getaddrinfo(3).
SEE ALSO
accept(2), bind(2), getsockname(2), listen(2), socket(2), path_resolution(7), selinux(8)